DIY -Tri Color Chain Weave


Wow, the bead store just received a shipment of new chain and the 4-in-1 chain has me so excited! If you have been following this blog for a while then you know I like to stitch things together, especially chain. The chain consists of a figure-8 links connected together by a large round link. The resulting effect looks very similar to flat 4-in-1 chain mail.  Chinese knotting cord is used to connect these chains side-by-side while adding a splash of color. The finished bracelet measures 7 1/4″.  Oh, the possibilities…enjoy and share your creations on our Facebook page.

Tools Neededtricolor materials
2 Pairs of chain nose pliers
Wire cutters
Hypo-tube cement

Materials Needed
1 1/2 feet 4-in-1 chain (can be all one color or use 6 inch lengths of different finishes for the tri-color effect)
2 yards Chinese knotting cord
1 D-ring toggle clasp
4 jump rings -6mm, 18 gauge
5 jump rings -4mm, 18 gauge
Medium twisted wire needles

Preparing the Materials

Step 1: Begin by cutting 3 equal lengths of chain that measure 6 inches each. Cut off the figure-8 link on each end of the chain so that the final link on each end is the larger center ring.

Step 2: Cut a 1 yard length of Chinese knotting cord and string a twisted wire needle onto it, doubling over one end by about a foot.

Weaving the Chains Together

The 4-in-1 chain is made up of figure-8 links that are connected together by a larger jump ring. The resulting effect looks very similar to flat chain-mail.  Chinese knotting cord is used to connect two of these chains side-by-side while adding a splash of color.

attachingcordStep 1: Rest two of the chains side-by-side so that the links of each chain are going the same direction.

Step 2: Attach the cord to the chains by feeding it through the first two side-by-side figure-8 loops. Leaving a 2 inch tail, tie the two cords together with a double knot.

Step 3: Feed the cord back through the same two links to secure the cord. (The first row of figure-8 links have now been connected together.)

weave1The basic weave pattern consists of wrapping the cord through two side-by-side links (this step keeps the chains flat) and then stepping up to the next row of figure-8 links by feeding the cord diagonally, between the two chains, and up through the next figure-8 link on the chain.

Step 4: “Step-up” to the next row by feeding the cord through the figure-8 link located one row up on the opposite chain. The cord will cross between the two chains diagonally.

Step 5: Connect the two chains together side-by-side by feeding the cord down through the corresponding figure-8 link of the opposite chain.

Step 6: Complete the stitch by feeding the cord back up through the figure-8 link of Step 4. (The next row of figure-8 links have now been connected together.)

twochainsStep 7: Repeat Step 4 through Step 6 until there is only one figure-8 link left to be stitched together.

Securing the Cords in Placeknot00Step 1: If needed, flip the piece over so that the beginning knot is on the side facing up. “Step-up” to the next row by feeding the cord through the figure-8 link located one row up on the opposite chain.

Step 2: Connect the two remaining figure-8 links together by feeding the cord around them twice so that the cord goes through each link two times.

Step 3: Feed the cord under the diagonally crossing cord from Step 1. (In the next steps, the cord will be secured in place by knotting it around this diagonal cord.)

gluetheknotsStep 4: Using a half-hitch knot, tie the cord around the diagonal cord.

Step 5: Make a 2nd knot around the same diagonal cord and pull the cord tight.

Step 6: Completely coat the knots with cement glue. Once the glue dries, about 10 minutes, cut off the excess cord close to the knot.

Step 7: Glue and cut the remaining cord from the knot on the opposite end of the chain.

 Adding Additional Rows of Chain3rdchain01Additional lengths of chain can be woven to either side of the finished piece. Use the same techniques outlined above to add a third length of chain.

Attaching the ClaspattachingaclaspThe clasp is attached to the center round link of each chain using a jump ring.

Step 1: Using chain nose pliers attach a 6mm jump ring to each of the outside chains and a smaller, 4mm jump ring to attach the center chain. Repeat on the other end of the bracelet.

Step 2: Use three 4mm jump rings to attach the toggle bar to one of the D-ring toggle components.

Step 3: Put it on, put it on and show someone!!!!

WE LOVE READING YOUR COMMENTS!! Comment on this post for your chance to win a kit of materials to make your own. Winner will be chosen randomly and announced on July 22nd!

Update: Congrats go out to Angi M. for winning the kit!!

About Lisa Claxton
Beads... what can I say, they are and have always taken over my life. Every room in the house has them and yet I crave more.

9 Responses to DIY -Tri Color Chain Weave

  1. Angela Mullis says:

    Love this design! Thank you for the tutorial! Pretty please count me in for this amazing giveaway! Thanks!

    Angi Mullis


  2. Lori F says:

    Love it, Lisa! I’m not an “olive” girl, but am seeing it in silver, turquoise and purple. Thanks for the tute! Pinning.


  3. Ruth Grimes says:

    Love this one! I really like the looks of chain mail, but have the worst time with the jump rings when I try to do it. Here is the answer….thanks!!


  4. arrowe4 says:

    How cute! Definitely one to add to the list. Thanks.


  5. Rosemary Patterson says:

    I know my granddaughter will love this! Thanks Lisa!


  6. Charlotte McCaig says:

    This is fabulous! I really thought it was chainmail…I’ve got to get some of this chain. I also love the toggle closure.Thanks for a chance to win.


  7. Vita says:

    Love the pre-made “chain mail” -its one of my faves, but I never have that much patience or time to make it!


  8. Lynn says:

    Lisa, thanks for posting this project! So pretty! Classy ‘chain mail’; really like the fun mix of colors and materials, can imagine using the cord weaving technique on other projects too. Looking forward to making one if I’m selected as winner ;-p


  9. Pingback: How to Make a Tri Color Chain Weave | Craft Collections

Leave a Reply

Fill in your details below or click an icon to log in: Logo

You are commenting using your account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s

%d bloggers like this: