DIY -Mixed Metal Lotus Pendant

lotusdrops2Besides being super sultry against the skin, one of the things I love about this design is its simplicity to make and all the possibilities for customization. Once you make a pendant you’ll find yourself making a pair of earrings to match. There are many different component pieces out there just waiting for you to embellish them with beads and wire! Enjoy.

Tools Neededlotusmaterials

Flush Wire Cutters
Chain Nose Pliers, 2 pairs are helpful

Materials Needed
1 Lotus petal drop link
27 inches of 2mm rolo chain
11, 4mm jump rings
1, 5mm jump ring
1 Toggle clasp
Ten 2.5mm crystal rondelles
Five 2.5mm square beads
One foot of 26 gauge wire
Eight 2.25mm metal hex-cut spacer beads

Wiring the Beads to the Lotus Frame

Each segment of beads is attached to the frame with a 3 inch length of wire. The wire coils used to secure the beads to the frame wrap upward, toward the point of the frame, allowing for proper spacing between the bead rows. Steps1-2Step 1: Secure one end of the wire to the frame by laying the wire across the face of the frame and wrapping a 1″ tail around the frame, toward the top, three times. The resulting coil should be tight with each coil resting against the previous one.

Step 2: Using flush wire cutters, cut the wire tail off, close to the frame. If the wire end is sticking out, squeeze it down with a pair of chain nose pliers.

Step 3: String 3 crystal beads onto the wire and position the coil on the frame so that all three beads fit within the frame.Steps4-5Step 4: Secure the wire in place by wrapping it tightly around the frame three times, toward the top of the frame. Use the chain nose pliers to help pull the wire tight.

Step 5: Using flush wire cutters, cut the remaining wire close to the frame.addingbeadrowsStep 6: Continue adding rows of beads using the same techniques outlined in Steps 1 thru 5. Make certain that each row accommodates the beads within the spacing of the frame, adjust the number of beads if needed.

The pattern for each row is as follows:
Row 1: Three crystal beads (this row has been completed)
Row 2: Five 2.5mm square metal beads
Row 3: Seven crystal beads
Row 4: Eight Hex-cut beads

Adding the Chain Fringechainfringe

Step 1: Using wire cutters, cut the following measured length of chain: 2 pieces measuring 1/2″ each, 2 pieces measuring 3/4″ each, 2 pieces measuring 1″ each, 2 pieces measuring 1 1/4″ each, and 1 piece measuring 1 1/2″ in length.

Step 2: Organize the chains by size on your working surface so that the longest chain length is in the middle and the shortest lengths are on the outside edge. Organizing the chains ahead of time will make attaching them easier.

Step 3: Using chain nose pliers, attach the chain lengths to the bottom of the frame with a 4mm jump ring. Make sure to close the ring tight so that the chains do not fall off later.

Attaching the Necklaceaddingchain-clasp

Step 1: Using wire cutters, cut the remaining chain to 18″.

Step 2: Connect a 5mm jump ring to the top of the frame and feed the chain length through it.

Step 3: Connect the clasp to the last link of one end of the chain with a 4mm jump ring.

Step 4: Connect a 5mm jump ring into the last link of the opposite end of the chain.

 

WE LOVE READING YOUR COMMENTS!! Comment on this post for your chance to win a kit of materials to make your own. Winner will be chosen randomly and announced on August 12th!

 

About Lisa Claxton
Beads... what can I say, they are and have always taken over my life. Every room in the house has them and yet I crave more.

8 Responses to DIY -Mixed Metal Lotus Pendant

  1. kjwinston says:

    OKAY HOW MUCH DO I LOVE THIS DESIGN AND THIS TUTORIAL???? Thank you for doing this – it hit my inbox just as I was feeling vastly overwhelmed by very un-fun work and this just lifted my spirits. GIMME, GIMME, GIMME.

    Liked by 1 person

  2. Ruth Grimes says:

    Another wonderful design from you, Lisa! It looks fantastic, and at the same time, very doable. Thanks!

    Like

  3. OMG! I have to say, like your design and inspiration. You are a DIY genius.
    😀

    Like

  4. Wonderful post! We are linking to this particularly
    great content on our website. Keep up the great writing.

    Like

  5. charrettemetalcrafts says:

    I just found this blog and I am the definition of excitement!!! Your tutorials are so clearly written. Now I just need to make more money to buy all the things to make more stuff. Typical plight of the creative individual.

    Like

  6. Very Beautiful & Thanks for sharing. Keep posting like this.
    Beads-usa-beading
    Allover Designs

    Like

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s

%d bloggers like this: